Lithium Battery

In 3S 10A 12V 18650 Lithium Battery Charger Board Protection Module, 3S stands for 3 18650 batteries or polymer lithium battery series combination. With 10.8V rated voltage for polymer battery, 11.1V 18650 or 3.7V lithium battery rated voltage and 12.6V lithium battery can be charged. And discharge 10A (referring to the maximum discharge current limit) Lithium battery protection board it also Comes with over-charge, over-discharge, over-current, short circuit protection.

Formula expansion :

1C battery expansion, 2000 capacity is equal to 2AH x 1 = 2A upper limit of current.
3C battery expansion, 2000 capacity equal to 2AH x 3 = 6A upper operating current.

If the battery gets heated, does not apply that battery, such a situation cannot be long-term use, the battery will soon be damaged.

Notes :

1: strictly according to the drawing wiring 0 V (B), 3.7 V (B1), 7.4 V (B2), 11.1 V (B +), not intentionally short circuit!
2: Once you have charged the first line, it will have output.
3: When connecting three battery groups, please make sure that the voltage of each battery group, if not the same, fill each battery separately and then use it in series. discharge test, the fastest battery voltage drop, which group is low battery. (2 good battery + a use effect = 3 low battery low battery use effect).

Warning:

The protection board can not be used for lithium iron phosphate batteries, lamp hernia, hand drill battery, electric battery fish, electric bicycle battery, car battery for children, 775 (4A) motor, 1 W fish eye LED light, please pay attention customer purchase connection! Described in terms of power for the following products: Massager rechargeable battery, LED ready light power supply, 12 V electronic products, solar street lamp battery, power backup monitor, and other products.

Features:

1. Operating current : 6 8A
2. Current limit : 10 13A
3. Storage condition : -40 +80 
4. Resting current: less than 30uA
5. Effective lifetime: over 30,000 hours
6. Internal resistance: less than 100mΩ
7. Short-circuit protection: protection
8. Self-recovery delay

1 x 3S 10A 12V 18650 Lithium Battery Charger Board Protection Module.

This 4S 14.8V 10A Lithium battery Protection Board comes with over-charge, over-discharge, over-current and short circuit protection, for a variety of various shapes 3.7V lithium-Ion batteries. HX-4S-A01 is Small size, suitable for many requirements of high integration, low cost of the occasion, to meet a wide range of performance requirements to ensure that the battery pack is absolutely safe and reliable.

1. Small power inverter
2. Massager battery pack
3. LED lamp backup power
4. Electronic products
5. Solar street lamp battery pack
6. Monitoring standby power supply.

1. This protection board is suitable for 4 series Li-ion cell.
2. Adopt a precision integrated circuit for fast and safe charging.
3. Support overcharge protection, over-discharge protection, and short circuit protection.
4. This product has gone through load and ageing test for quality assurance.

The 3 Series 40A 18650 Lithium Battery Protection Board 11.1V 12.6V with Balance for Drill Motor Lipo Cell Module comes with recovery function-AUTO Recovery and Integrated 10 low load resistance MOS tube.

It provides a continuous discharge of 40A, 100mA balanced current, for electric drill/sprayer/LED lights/low power inverter.  (if the cooling environment is not good, please reduce the load current use).

The Scope of Nominal voltage of 3.6V, 3.7V lithium battery (including 18650,26650, a polymer lithium battery) where Charging voltage can be range between 16.8V to 18.1V The board operates smoothly with Continuous charge current of (upper limit): 20A. The balanced version is suitable for starting current below 80A, power 135W below the drill (with balance).

The Board comes in a size of approx. 46 x 60 x 3.4 mm which can be easily installed in a compact size or on battery bundle itself.

Features:

• 3S 11.1V 12.6V 40A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery).
• Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery).
• Continuous discharge current (upper limit): 40A (if the cooling environment is not good, please reduce the load current use).
• Continuous charge current (upper limit): 20A.
• Suitable for the drills with starting current below 80A, power 135W below.

Specifications:

This TP4056 1A Li-Ion Battery Charging Board Type C with Current Protection is a tiny module, perfect for charging single cell 3.7V 1 Ah or higher lithium-ion (Li-Ion) cells such as 16550s that don’t have their own protection circuit. Based on the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished.

Furthermore, when the battery voltage drops below 2.4V the protection IC will switch the load off to protect the cell from running at too low of a voltage – and also protects against over-voltage and reverse polarity connection (it will usually destroy itself instead of the battery) however please check you have it connected correctly the first time.

Manufactured under fully machinery processing. Each module is tested OK before shipment from Robu.in so it has high reliability for the best performance. In conclusion, it is a special design for a single lithium battery charging. TP4056 Other features include the current monitor, under-voltage lockout, automatic recharge, and two status pin to indicate charge termination and the presence of an input voltage.

1. Connect Type C cable for power, or 5V DC to pads marked IN+ and IN- on the left-hand side of the module
2. Connect cell to charge to B+/B- pads on the right-hand side of the module.
3. A load (something for the battery to power) can be connected to the OUT+/OUT- pads on the right-hand side
4. Important! Disconnect load when charging
5. The red LED indicates charging in progress, the green LED indicates charging has finished.
6. Never charge your battery at a rate greater than 1C.

1. Ampere meter can only be connected to a 5v input end of the module.
2. It is better than the charging current is 37% of the battery capacity. If you charge the battery of 1000mAh, a current of 400mAh is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protection function, auto-subtract the charging current to avoid burn damage to the chip.
6. NO Reverse polarity.

1. Led indicator: Red is charging Green is fully charged.
2. Current Protection: Yes
3. Inversed polarity: NO.
4. Use mature charging chip TP4056 for simple peripheral circuits, good protection performance, and high charging accuracy.
5. Fully machinery automated processing, all patch parts manufacturing.
6. Input interface: Type C
7. Current Protection: Yes
8. Charging mode: Linear charging.
9. Current: 1A adjustable.
10. Charge precision: 1.5%.
11. Input voltage: 4.5V-5.5V.
12. Full charge voltage: 4.2V.

3S 11.1V 10A 18650 Lithium Battery Overcharge And Over-current Protection board (BMS) ensures the security of battery pack. This battery management system design and Suitable for: 10.8V (Rated voltage of polymer battery) 11.1V (18650 or 3.7V lithium battery rated voltage) 12.6V (Lithium battery full charge voltage)

Note: Please allow 1-3mm errors due to manual measurement. Item color displayed in photos may be showing slightly different on your computer monitor since monitors are not calibrated same

Also, Note down and take care of following things while using 3S 11.1V 18650 Lithium battery protection board 12V 10A Overcharge And Overcurrent protection.

1. Higher than 3A current discharge product, the discharge rate of battery discharge is above 3C.
2. Multiplier calculation formula: 1C battery, 2000 capacity is equal to 2AH * 1 = 2A maximum working current.
3. 3C ratio battery, 2000 capacity is equal to 2AH * 3 = 6A maximum working current.
4. When the battery in series 3, please ensure that the voltage of each battery is the same, if not the same, please fill in each set of batteries and then use When the discharge is tested, the battery in which the voltage drop is the fastest is the difference between the battery and the battery.
5. After the line is connected to the need to charge (charge voltage 12.6V) activation, there will be output.
6. 3A current above the discharge products, the battery discharge rate to 3C or more.Formula: 1C ratio of the battery, the 2000 capacity is equal to the maximum operating current 2AH*1=2A.3C ratio of the battery, the 2000 capacity is equal to the maximum working current 2AH*3=6A.in the use of the battery will be the battery power is not applicable, this situation must not be used for a long time, the battery will soon be damaged. Description interpretation.
7. 3 Series (series combination of 18650 3 batteries or lithium polymer batteries)
8. 10.8V (polymer battery rated voltage)
9. 11.1V (18650 or 3.7V lithium battery rated voltage)
10. 12.6V (lithium battery voltage)In the process of use, if the battery heat, the battery power is not applicable. This situation cannot be used for a long time. Otherwise, the battery will soon be damaged.

1. Three series of lithium battery protection board.
2. Automatically cancel protection after protection conditions restore.
3. With the function of overcharge protection, over discharge protection, short circuit protection, over-current protection.
4. Suitable for lithium battery pack of 11.1V, 12V, 12.6V.
5. Quiescent current < 30uA, so power consumption is small.

This is an original 1200mAh 18650 battery. 18650 battery is a Li-ion rechargeable battery with a 1200mAh Battery Capacity. This is not a standard AA or AAA battery but is very useful for applications that require continuous high current or high current in short bursts like in cameras, DVD players, iPod, etc. A 18650 cell can be charged and discharged up to 1000 cycles without much loss in battery capacity. They are safe to use, environment friendly and have long battery life. It comes with high energy density and provides excellent continuous power sources to your device. It should be used with a protection circuit board that guards the battery against over-charge, over-discharge of the pack, and avoid over-current drawn.

• High energy density
• High working voltage for single battery cells.
• Pollution-free
• Long cycle life
• No memory effect
• Capacity, resistance, Voltage, platform time consistency is good.
• Good consistency and low self-discharge.
• Lightweight, small size
• Shape: Cylindrical Battery
• Battery Type: Lithium-Ion Battery
• High performance and capacity
• Flat top to suit many devices fitting.

• Electric Scooter
• Electric Bicycle
• E-Skate Board
• Electric Motorcycle
• E-Wheel Chair
• Electric Tool
• Drone
• Electric Vehicle Etc.
• Power Bank

• Nominal Voltage : 3.7V
• Max Charge Voltage : 4.2V
• Discharge Voltage : 2.8V
• Form Factor : 18650
• Life cycle : 200 Cycles
• Rechargeable : Yes
• Capacity : 1200mAh
• Weight :  35gm
• Height : 65mm
• Diameter :  18mm

2S 3A Li-ion Lithium Battery 7.4V 8.4V 18650 Charger Protection Board Module is a small PCB mounted Li-ion Lithium Battery charger protection module. This small and smart battery charger protection module comes with various features like Short circuit protection, Overcharge protection, Over-discharge protection, Overcurrent protection. It is very easy to install and convenient to use in all your DIY portable projects.

Features :

• Over-Discharge Detection Voltage: 2.3-3.0V±0.05V.
• Maximum Working Current: 3A.
• Transient Current: 5A.
• Operating Temperature : -40-50 C.
• Internal Resistance: Less than 45m Ω.
• B+ B-: The interface of battery core.
• P+ P-: The connector of the battery board.
• MB: The connection point between the batteries.

Specifications:

Pin Descriptions: 

• B+ B-: The interface of battery core
• P+ P-: The connector of the battery board
• MB: The connection point between the batteries
• B+: Battery V+ Positive
• B-: Battery V- Negative
• P+: Output / Charging V+
• P-: Output / Charging V-

Package Includes :

• 1 x 2S 3A Li-ion Lithium Battery 7.4V 8.4V 18650 Charger Protection Board Module.

Note:

• The protection board cannot be used for lithium iron phosphate batteries, hernia lamps, hand drill battery pack, electric fish battery pack, electric bicycle battery pack, buggy battery, 775 (4A) above the motor, 1W fisheye LED lamp.

This battery type capacity indicator module display shows the display is more intuitive and more beautiful. A wider range of applications, nickel-metal hydride batteries, 18650 and polymer lithium battery packs, lead-acid storage, electric vehicle batteries, e
lectric equipment can be used.

This display has a reverse connection function, even if the positive and negative connection will not burn. To use the display just connect the positive and negative terminals of the display board to the positive and negative terminals of the battery under test. The digital tube will display the real-time battery power.

BMS (Battery Management System) a battery management system that is designed to monitor the status of batteries, control the process of charging/discharging the battery, etc.

This BMS charge-discharge controller module comes with pre-soldered nickel strip ready to use for a single 18650 rechargeable cell.The module has protection against short circuit, overcharge and over-discharge.One of the functions of the charge controller is to turn off the power supply for the batteries when the maximum capacity of at least one battery is reached.This BMS controller is designed for more than 30,000 hours of operation.The maximum allowable current is 5A.

If the maximum permissible value of the supply voltage is exceeded, the charge controller activates the protection mode.In order to restore the module, it is necessary to re-apply voltage to the input of the BMS board or wait a while until the charge controller automatically disables protection.

1. Small size designed for a four-cell battery pack.
2. Simple and convenient circuit for easy connections
3. Over-charge/Over-discharge Protection.
4. Pre-soldered Nickel Strip ready to mount on battery.

1 x 1S 5A 18650 Lithium Battery Protection Board