GU Impex

The NRF24L01 module is the latest in RF modules. This module uses the 2.4GHz transceiver from Nordic Semiconductor, the NRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the 2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Antenna and add some extra pipelines, buffers, and an auto-retransmit feature – very nice!

This board features a reverse polarized SMA connector for maximum RF range. And there is PA and LNA circuit on board, with the external antenna it can reach long distance than the one without these parts.

This module comes with the 2.4G antenna (2DB), with a 250Kbps transmission rate on open-air it can reach the 800-1K meters communication distance.

This wireless Transceiver module is an easy and suitable module if you want to set up your wireless communication system at a low cost!! It can achieve a good balance between wireless transition performance and cost!

You can easily add it with your own MCU/ARM/PIC/AVR/STM32 system! What’s more, this nRF24L01+ module is designed with the Power amplifier and SMA antenna This allowed you to use the wireless communication up to 1000 meters! (No barrier)

1. It uses 2.4GHz global open ISM band, with license-free.
2. Transmit power is greater than +20 dBm.
3. Support six-channel data reception.
4. 2Mbit/s speed makes high-quality VoIP possible
5. Multi-frequency points: 125 frequency points meet the needs of multi-point communications and frequency hopping.
6. Low cost: integrated with high-speed signal processing parts associated with RF protocol, such as: automatically re-send lost packets and generate acknowledge signal;
7. SPI interface facilitates the communication with MCU I/O port.
8. Facilitate the development for customers, without development RF part.
9. Software programming is fully compatible with NRF24L01 modules.

1 x 2.4GHz NRF24L01 Transceiver module.

1 x SMA Antenna.

The NEO-6MV2 is a stand-alone GPS (Global Positioning System) module featuring a high-performance 50 channel U-Blox 6 positioning engine. The NEO6MV2 GPS module checks for location on Earth and provides the Latitude and Longitude of the position it is in. This is a low-cost module with a detachable antenna, which also comes with a logic level converter and a voltage regulator, which makes it compatible with both 5V and 3.3V powered boards like Arduino Uno, Mega, Pro Mini, etc. It can be used in the Navigation Systems of Smartphones and Tablets, Drones, in location-based services, etc.

• Robust & high accuracy
• Board size: 23mm*40mm
• Compatible with 3.3V-5V interface
• Compatible with all versions of Arduino
• EEPROM to save configuration settings
• Separated 18X18mm GPS antenna
• Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
• Maximum navigation update rate: 5Hz
• Default baud rate: 9600bps
• EEPROM with battery backup
• Sensitivity:  -160dBm
• Supply voltage: 3.6V
• Operating temperature range: -40ºC TO 85°C

To power the device, you can either connect your 5V pin or 3.3V pin to VCC and connect GND. As it communicates at 9600 bps via UART TTL logic, you need to connect TX and RX pins to respective pins on your controller and get the GPS coordinates of your position.

Datasheet of NEO-6MV2 Module

Interface Neo6M GPS Module with Arduino

Interface Neo6M GPS Module with Raspberry Pi

1×NEO-6MV2 GPS Module

1× Detachable Antenna

The NEO-7M-000 GPS Module is a compact and versatile navigation device designed for MultiWiiCopter (MWC) and APM2.5 flight control systems. Featuring an EEPROM for storing configuration data, the GY-NEO 7M V2 offers precise positioning and navigation capabilities. Its compatibility with MWC and APM2.5 makes it an ideal choice for drone and UAV applications.

1.  Module with a ceramic active antenna.
2. With data backup battery.
3. LED signal indicator.
4. Compatible with various flight controller module
5. EEPROM saves the configuration parameter data when power-down.
6. Module with ceramic destined antenna, signal super
7. quality Immersion Gold PCB

1 x NEO-7M-000 NEO-7M GPS Module MWC GY-NEO 7M V2 Flight Control GPS Module EEPROM MWC APM2.5

SIM7600EI is a complete multi-band LTE-FDD/LTE-TDD/HSPA+/UMTS/EDGE/GPRS/GSM module solution in LCC type which supports LTE CAT1 up to 10Mbps for downlink and 5Mbps for uplink data transfer. Designed in the compact and unified form factor, SIM7600EI is compatible with SIMCom HSPA+ SIM5360 module/LTE CAT3 SIM7100 and LTE CAT4 SIM7600E-H module, which allows the customer to design their application once for different technology and benefit from great development time-saving

This SIM7600EI 4G LTE High-Speed Modem GPS/GNSS IoT board has strong extension capability with rich interfaces including UART, USB2.0, SPI, I2C, Keypad, PCM, etc. With abundant application capabilities like TCP/UDP/FTP/FTPS/HTTP/HTTPS/SMTP/POP3 and MMS, the module provides much flexibility and ease of integration for the customer’s application.

1. Unzip driver file (Given in an Attachment)
2. Open Mange from My computer
3. Open  device manager
4. Right-click on LPT &COM Port
5. Click on port & open properties
6. Install driver & provide a path of unzipping the file. (select drivers as per your system OS: Windows 7, Windows 8, etc)

1. LTE-TDD B40/B41
2. LTE-FDDB1/B3/B5/B8
3. UMTS/HSPA+ B1/B8
4. GSM/GPRS/EDGEB3/B8
5. LCC Package
6. Control Via AT Commands
7. 3GPP E-UTRA Release 11
8. USB Driver for Microsoft Windows 2000/XP/Vista/Win7/Win/Win10
9. USB Driver for Linux /Android
10. RIL supporting for Android 2.4/4.0/5.0/6.0/7.0
11. MBIM to Win8
12. Firmware update via USB
13. TCP/IP/IPV4/IPV6/Multi-PDP/FTP/FTPS /HTTP/HTTPS/DNS
14. SSL3.0/TLS1.0/TLS1.2
15. DTMF (Sending and Receiving)
16. Audio Playing
17. USB Audio and VoLTE
18. FOTA

1 x SIM7600EI 4G LTE High-Speed Modem GPS/GNSS IoT board Raspberry Pi Compatible

SIMCOM SIM28ML GPS module is a standalone or A-GPS (Assisted Global Positioning System) receiver. With Built in LNA, SIM28ML can relax antenna requirement. It can also track as low as -165 dBm signal even without network assistance. And has excellent low power consumption characteristics (acquisition 16 mA, tracking 15 mA). It supports various location and navigation applications, including autonomous GPS, QZSS, SBAS ranging (WASS, EGNOS, GAGAN, MSAS), RTCM and A-GPS.

It has strong extension capability with rich interfaces including UART, USB2.0, I2C, GPIO etc. With abundant application capability like TCP/UDP/FTP/FTPS/HTTP/HTTPS/DNS, the module provides much flexibility and ease of integration for customer's application.

• TDD-LTE B38/B40/B41
• FDD-LTE B1/B3/B5/B7/B8/B20
• WCDMA/HSDPA/HSPA+ B1/B5/B8
• GSM/GPRS/EDGE 900/1800 MHz
• Control Via AT Commands
• 8B;standalone;assisted,XTRA

• LTE CAT1
  • Uplink up to 5Mbps
  • Downlink up to 10Mbps
• HSPA+
  • Uplink up to 5.76 Mbps
  • Downlink up to 42 Mbps
• UMTS
  • Uplink/Downlink up to 384Kbps
• EDGE Class
  • Uplink/Downlink up to 236.8Kbps
• GPRS
  • Uplink/Downlink up to 85.6Kbps

• USB Driver for Microsoft Windows 2000/XP/Vista/Win7/Win8/Win10
• USB Driver for Windows CE
• USB Driver for Linux /Android
• RIL supporting for Android/Windows CE
• Automatic installation for windows
• Firmware update via USB
• TCP/IP/IPV4/V6 Multi-PDP,MT PDP
• FTP/FTPS/HTTP/HTTPS/DNS
• DTMF
• MBIM to Win8
• Source code of the PC manager of the device for reference

• USB2.0
• UART  
• Product Specification

  Model Name/Number	Sim7600e H
  Usage/Application	Industrial
  Brand	Simcom
  Output Voltage	3.4V~ 4.2V
  Size/Dimension	30x30x2.9mm
  Weight	5.5g

• SIMCOM A7670C-LASS LTE 4G Module Cat-1
• SIM A7670C 4G LTE Development Board
• SIM800C 32M GSM Module IC with 32M Flash
• SIM800C GSM GPRS Chip Module
• SIM28ML GPS Module – LCC 18pin
• Sim900
• Sim800a
• Sim868
• Sim808
• Sim5300e
• Sim7600e
• Sim5360e  .

If you want to detect methane gases with your projects, you will need sensors. If you need any data on the sensitive material then, the MQ-4 High Sensitivity Gas Methane (CNG) Detector Gas Sensor Module is a quite good solution.

This is a simple to use MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module which can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc in the air. The module uses our MQ-4 sensor. It simplifies the interface to the odd pin spacing of the sensor and provides the interface through standard 4 x 0.1″ header pins.

It provides an analog output corresponding to the concentration of the gases in the air and an easy-to-use digital output. The onboard potentiometer can be used to set the maximum gas concentration beyond which the digital output gets triggered. The MQ-4 can detect natural gas concentrations anywhere from 200 to 10000ppm.

Just power the module with 5V set the threshold and you can start getting the gas concentration of the air around the sensor! An onboard LED signals the presence of any gas.

The digital output can be easily interfaced with microcontrollers and other circuits. The analog output can be hooked up to an ADC of a microcontroller to get a wide range of sensor readings. This is a simple-to-use compressed natural gas (CNG) sensor, suitable for sensing natural gas (composed of mostly Methane [CH4]) concentrations in the air.

If you want to explore the more variety of gas sensors, then click on the link  Gas Sensor

1. Signal output indicator
2. Dual Signals output (analog output and TTL output)
3. The TTL output signal is low level, allows to connect with SCM directly
4. Analog output 0~5V voltage
5. High sensitivity
6. Long working life and stable performance
7. Quick response and recovery.

1 x MQ-4 High Sensitivity Gas Methane (CNG) Detector Sensor Module

• Send Text Messages (SMS)
• Make or receive Phone calls
• Connect to Internet via GPRS
• TCP/IP

SIM5360 series is Dual-Band HSPA+/WCDMA and Dual-Band GSM/GPRS/EDGE module solution in a SMT type which supports HSPA+ up to 14Mbps for downlink data transfer. It has strong extension capability with rich interfaces including UART, USB2.0, SPI, I2C,Keypad, PCM, etc. With abundant application capability like BMP, TCP/UDP/FTP/FTPS/ HTTP/HTTPS/SMTP/POP3 and MMS, the module provides much flexibility and ease of integration for customer’s application.

• Dual-Band UMTS/HSPA+ 900/2100MHz
• Quad-Band GSM/GPRS/EDGE 900/1800MHz
• GPRS multi-slot class 12
• EDGE multi-slot class 12
• Output power
  • UMTS 850/1900: 0.25W
  • - UMTS 900/2100: 0.25W
  • - GSM850/GSM900: 2W
  • - DCS1800/PCS1900: 1W
• Control Via AT Commands
• Interfaces
  • USB2.0/UART/SIM card/SPI/I2C/GPIO/RTC/ADC/PCM/SDIO
• Supply voltage range: 3.4V~ 4.2V
• Operation temperature: -40°C to +85°C
• Dimension: 30 X 30X 2.9 mm

•  CELL assistant Location (No GPS)
• A-GPS: MS-Based, MS-Assisted
• Stand-alone GPS
• QUALCOMM XTRA GPS mode
• GLonass

•  HSPA+
  • Max. 14.4Mbps(DL), Max.5.76Mbps(UL)
•  WCDMA
  • Max.384Kbps(DL), Max.384Kbps(UL)
• EDGE Class:
  •  Max. 236.8Kbps(DL),Max.118Kbps(UL)
•  GPRS
  • -Max. 85.6Kbps(DL), Max.42.8Kbps(UL)
• CSD
  •  GSM data rate 14.4Kbps
  •  WCDMA data rate 57.6Kbps
  • -WCDMA 64kbps CSD for Video call .

The Sim800C GPRS/GSM Shield with Antenna provides you with a way to use the GSM phone network to receive data from a remote location and it is compatible with all boards which have the same form factor (and pinout) as a standard Arduino Board. This shield can also be applied to DIY phones for calling, receiving and sending messages, making GPS trackers or other applications like Smart home, etc.

SIM800C GPRS/GSM Shield delivers GSM/GPRS850/900/1800/1900MHz signals for Audio, SMS and GPRS Service. Also, it runs at the low power consumption of about 0.6mA in sleep mode but acts compliant to GSM phase 2/2+: Class 4 (2 W @850/ 900 MHz), Class 1 (1 W @ 1800/1900MHz) with a two-in-one headset jack.

What''s more, to make your project more flexible and efficient, we have prepared two different antennas for you. One is the traditional GPRS antenna which is more sensitive while another one is an onboard antenna which is more compact and easy to install.

1. Quad-Band 850/ 900/ 1800/ 1900 MHz
2. GPRS multi-slot class 10/12
3. GPRS mobile station class B
4. Compliant to GSM phase 2/2+
5. Onboard Provision for Mic and Speaker.

1. Chip used: QUAD BAND SIM800C GSM CHIP.
2. Arduino compatibility: Arduino UNO R3, Arduino Mega etc.
3. Antenna type: finger antenna.
4. Output: TTL and RS232 serial output.
5. Simcard holder: standard size.
6. Buzzer for CALL and SMS indication.
7. Indication LEDs
   PWR Power Indication
   STS Status Indication
   NTW Network Indication
8. PINOUTS:
   o2 RX
   o3 TX
9. Provision for the headphone jack, mic, and speaker.

1 x Sim800C GPRS/GSM Shield with Antenna.

SIMCOM A7670C-LASS LTE 4G Module is The Cat-1 Module which supports wireless communication modes of LTE-TDD/LTE-FDD. It supports maximum 10Mbps downlink rate and 5Mbps uplink rate. A7670 provides 124 pins, including 80 LGA pins in the outer ring and 44 LGA pins in the inner ring.

The SIMCOM A7670C series adopts LGA form factor and is compatible with SIM7000/SIM7070 series(NB/Cat M modules), and SIM800A/SIM800F(2G modules), which enables smooth migration from 2G/NB/Cat M products to LTE Cat 1 products, and greatly facilitates more compatible product design for the customer needs.

The SIMCOM A7670C-LASS supports multiple built-in network protocols, supports drivers for main operation systems(USB driver for Windows, Linux and Android etc.) and software function, AT commands are compatible withSIM7500/SIM7600 series modules. Meanwhile the A7670series integrates main industrial standard interfaces, with powerful expansibility, including abundant interfaces such as UART, USB, I2C, GPIO, which is suitable for main IOT applications such as telematics, surveillance devices, POS, industrial routers, and remote diagnostics etc.

• Small size LTE Cat 1 module
• LGA form factor with abundant interfaces
• Suitable for LTE only
• Abundant software functions: FOTA, LBS, SSL
• The form factor of A7670 series are compatible with the SIM7000/SIM7070 series
• Supported Band: LTE-FDD B1/B3/B5/B8 , LTE-TDD B34/B38/B39/B40/B41

• SIMCOM A7670C-LASS LTE 4G Module Cat-1

  SIM A7670C 4G LTE Development Board

  SIM800C 32M GSM Module IC with 32M Flash

  SIM800C GSM GPRS Chip Module

  SIM28ML GPS Module – LCC 18pin

  Sim900

  Sim800a

  Sim868

  Sim808

  Sim5300e

  Sim7600e

  Sim5360e

SIM900A Modem is built with Dual Band GSM based SIM900A modem from SIMCOM. It works on frequencies 900MHz. SIM900A can search these two bands automatically. The frequency bands can also be set by AT Commands. The baud rate is configurable from 1200-115200 through AT command. SIM900A is an ultra compact and wireless module. The Modem is coming interface, which allows you connect PC as well as microcontroller with RS232 Chip(MAX232). It is suitable for SMS, Voice as well as DATA transfer application in M2M interface. The onboard Regulated Power supply allows you to connect wide range unregulated power supply. Using this modem, you can make audio calls, SMS, Read SMS, attend the incoming calls and ect. through simple AT commands. This is a complete GSM module in a SMT type and made with a very powerful single-chip, allowing you to benefit from small dimensions. SIM 900A GSM Modem with serial and TTL outputs. 

Features:-

• Quad-Band GSM/ 850/900/1800/1900MHz
• Compatible with arduino, raspberry pi, arm, avr, pic, 8051
• power supply 12v 1amp to 2 amps max
• Use in the area of full signal strength.
• Perfect suited for GSM based Microcontroller Projects (better than SIM300 and other GSM Modems)
• Option for connecting MIC and SPEAKER directly to GSM MODEM for calls (LINE IN also available)
• Supports communication through RS232 with DB9 Connector, TTL Pins and I2C Pins
• CALL SMS GPRS facility - MIC input, LINE input and SPEAKER output pins.

SIM800C GSM GPRS Chip Module. It can transmit voice, SMS, and data over GSM. The SIM800C GSM/GPRS Module from SIMCOM is a popular module for adding GSM/GPRS/Bluetooth support to any electronic device. The module is very inexpensive and requires very few external components. It has applications in a variety of fields, including IoT, data monitoring, remote control, factory automation, and so on. SIM800C is a Quad Band GSM Module with 42 pins in an SMT Package. The module is also very small, measuring only 17.6 x 15.7 x 2.4mm. This module can transmit voice, SMS, and data, as well as use Bluetooth for data transmission, all while consuming very little power. As a result, it is an appropriate choice when the final device has a small footprint and a compact design. More Detail.

Features

• Quad Band GSM / GPRS Module
• Can transmit voice, SMS, and data over GSM
• Low Power Consumption
• Embedded TCP/UDP protocols
• LCC form factor, easy for solder
• Abundant software functions: DTMF, MMS, MUX

Quectel EG91-EX is an IoT/M2M-optimized LTE Cat 1 Module

Quectel EG91 is a series of LTE category 1 modules optimized specially for M2M and IoT applications. Adopting 3GPP Rel. 11
LTE technology, it delivers maximum data rates up to 10Mbps downlink and 5Mbps uplink. These make EG91 an ideal solution
for numerous IoT applications that are not reliant on high speed connectivity but require the longevity and reliability of LTE
network.

EG91 contains 6 variants: EG91-E, EG91-EX, EG91-NA, EG91-NS, EG91-VX and EG91-NAX. EG91 is pin-to-pin compatible with
Quectel UMTS/HSPA+ module UG95/UG96 and LPWA module BG95/BG96. And it is backward-compatible with existing GSM/
GPRS and UMTS/HSPA+ networks, ensuring that it can be connected even in remote areas devoid of 4G network coverage.

A rich set of Internet protocols, industry-standard interfaces and abundant functionalities (USB serial drivers for Windows
7/8/10, Linux and Android, etc.) extend the applicability of the module to a wide range of M2M and IoT applications such as
smart metering, wearable devices, environmental monitoring, asset tracking, fleet management, security and alarm systems
and so on.

Features:

• low-power LTE connectivity optimized for broadband IoT applications.
• Multi-band LTE, UMTS/HSPA+ and GSM/GPRS/EDGE coverage
• Compact SMT form factor ideal for size-constrained applications with extended operation temperature range
• Embedded power management unit (PMU) featuring ultra-low deep-sleep current consumption
• Simple migration from 2G/3G to 4G with a flexible and scalable platform

The SIM800A Quad-Band GSM/GPRS Module with RS232 Interface is a complete Quad-band GSM/GPRS solution in an LGA(Land grid array) type which can be embedded in the customer applications. SIM800A support Quad-band 850/900/1800/1900 MHz, it can transmit Voice, SMS and data information with low power consumption.

With a tiny size, it can fit into slim and compact demands of custom design. Featuring and Embedded AT, it allows total cost savings and fast time-to-market for customer applications.

The SIM800A modem has a SIM800A GSM chip and RS232 interface while enables easy connection with the computer or laptop using the USB to the Serial connector or to the micro-controller using the RS232 to TTL converter. Once you connect the SIM800A modem using the USB to RS232 connector, you need to find the correct COM port from the Device Manager of the USB to Serial Adapter.

Then you can open Putty or any other terminal software and open a connection to that COM port at 9600 baud rate, which is the default baud rate of this modem. Once a serial connection is open through the computer or your micro-controller you can start sending the AT commands. When you send AT commands for example “AT\r” you should receive back a reply from the SIM800A modem saying “OK” or other response depending on the command sent.

Features and Specifications of SIM800A Module :-

• SIM800A Quad Band GSM Module
• Bands: GSM 850MHz, EGSM 900MHz, DCS 1800MHz, PCS 1900MHz
• Coding schemes: CS-1, CS-2, CS-3, CS-4 Tx power: Class 4 (2W), Class 1 (1W)
• GPRS class 2/10.
• Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
• Voltage Supply Required- 9VDC to 12VDC with atleast 2A Peak Current Capability
• High-Quality Product (Not hobby grade).
• 5V interface for direct communication with MCU kit.
• TTL Rx and TTL Tx and DB9 Connector Based RS232 Outputs
• Configurable baud rate.
• Built-in SIM Card holder.
• Built-in Network Status LED.
• Inbuilt Powerful TCP/IP protocol stack for internet data transfer over GPRS.
• Low power.
• Operating temperature: -40C to +85C
• External Finger type antenna
• Weight - 40gm

Applications :- 

• Remote Data Monitor and Control.
• Water, gas and oil flow metering.
• AMR (automatic meter reading).
• Power station monitoring and control.
• Remote POS (point of sale) terminals.
• Traffic signals monitor and control.
• Fleet management.
• Power distribution network supervision.
• Central heating system supervision.
• Weather station data transmission.
• Hydro-logic data acquisition.
• Vending machine.
• Traffic info guidance.
• Parking meter and Taxi Monitor.
• Telecom equipment supervision (Mobile base station, microwave or optical relay station).
• SIMCOM A7670C-LASS LTE 4G Module Cat-1
• SIM A7670C 4G LTE Development Board
• SIM800C 32M GSM Module IC with 32M Flash
• SIM800C GSM GPRS Chip Module
• SIM28ML GPS Module – LCC 18pin
• Sim900
• Sim800a
• Sim868
• Sim808
• Sim5300e
• Sim7600e
• Sim5360e  .

The SIM808 GSM GPRS Module is For people who want to integrate a cellular (GSM/GPRS) module into their design without the full breakout, this hand-solderable module is pretty nice.You''''ll need to add all of the supporting circuitry that is required, such as antennas, power regulation, any level shifting, LEDs, etc

Features :

Quad-band 850/900/1800/1900MHz - connect onto any global GSM network with any 2G SIM (in the USA, T-Mobile is suggested)
Fully-integrated GPS (MT3336 chipset with -165 dBm tracking sensitivity) that can be controlled and query over the same serial port
Make and receive voice calls using a headset or an external 32Ω speaker + electret microphone
Send and receive SMS messages
Send and receive GPRS data (TCP/IP, HTTP, etc.)
PWM/Buzzer vibrational motor control
AT command interface with "auto baud" detection

Here''''s the GPS specifications:

22 tracking /66 acquisition channels
GPS L1 C/A code
Sensitivity
Tracking: -165 dBm
Cold starts : -147 dBm
Time-To-First-Fix
Cold starts: 30s (typ.)
Hot starts: 1s (typ.)
Warm starts: 28s (typ.)
Accuracy: approx 2.5 meters
Dimensions 24mm x 24mm x 3mm / 0.9" x 0.9" x 0.1"
Weight: 3.2g

SIMCOM A7670C-LASS LTE 4G Module Cat-1

SIM A7670C 4G LTE Development Board

SIM800C 32M GSM Module IC with 32M Flash

SIM800C GSM GPRS Chip Module

SIM28ML GPS Module – LCC 18pin

Sim900

Sim800a

Sim868

Sim808

Sim5300e

Sim7600e

Sim5360e  .

These connectors are designed to provide compatibility with industry-grade 50 ohm and 75ohm cables for longer operational life with gold and nickel plating for environmental protections.

Main Application of SMA Connectors:

• Aerospace and Defense: Hand-held field Device and Instrumentation
• Medical: Instrumentation
• Commercial Vehicle: Bluetooth and GPS
• Telecommunications: Wireless Base Stations, Cellular Mobile System
• Data/Communications: Wifi, WiMAX
• Industrial: Active and passive components, instrumentation, M2M Communications, Vehicle Tracking System.

1. Through Hole, Pcb Mount, Jack/female, Angled/90, 50;
2. Excellent electrical performance up to 18GHz with low reflection;
3. Thread type coupling mechanism ensure small loss and high security in a compact design;
4. High Quality with 30 days 100% Money back;
5. From the OEM Original Factory, same quality with much better price.

Electrical Characteristics

1. Impedance 50 ohm
2. Frequency Range:0~6 GHz
3. VSWR: Straight type 1.3max / R/A type 1.5max
4. Dielectric Withstanding Voltage: 1000 V rmsmin for RG142, RG405
   750 V rms min. for RG316, RG402
   500v rms min. for RG178
5. Working Voltage:500 V rms max. for RG142, RG405
   375 V rms max. for RG316, RG402
   170 V rms max. for RG178
6. Center Contact Resistance 6.0 m (Milliohms max.)
7. Outer Contact Resistance 2.0 m (Milliohms max.)
8. Insulation Resistance 5 x 10 m (Megohms min.)

Specifications:

Additional Information:

• Delivery Time: standard

These connectors are designed to provide compatibility with industry-grade 50 ohm and 75-ohm cables for longer operational life with gold and nickel plating for environmental protections.

Appliance:

• Aerospace and Defense: Hand-held field Device and Instrumentation
• Medical: Instrumentation
• Commercial Vehicle: Bluetooth and GPS
• Telecommunications: Wireless Base Stations, Cellular Mobile System
• Data/Communications: Wifi, WiMAX
• Industrial: Active and passive components, instrumentation, M2M Communications, Vehicle Tracking System

1. SMA Connector,Female,Straight,PCB Connector,Plate Edge Mount,Copper,Gold Plating;
2. Excellent electrical performance up to 18GHz with low reflection;
3. Thread type coupling mechanism ensure small loss and high security in compact design;

Electrical Characteristics

1. Impedance 50 ohm
2. Frequency Range: 0~6 GHz
3. VSWR: Straight type 1.3max / R/A type 1.5max
4. Dielectric Withstanding Voltage: 1000 V rmsmin for RG142, RG405
5. 750 V rms min. for RG316, RG402
6. 500v rms min. for RG178
7. Working Voltage:500 V rms max. for RG142, RG405
8. 375 V rms max. for RG316, RG402
9. 170 V rms max. for RG178
10. Center Contact Resistance 6.0 m (Milliohms max.)
11. Outer Contact Resistance 2.0 m (Milliohms max.)
12. Insulation Resistance 5 x 10 m (Megohms min.)

Mechanical Characteristics

1. Coupling: 1/4-36 thread
2. Contact Retention: 15 in-lbs min.
3. Coupling nut torque: 30 in-lbs. min.
4. Durability(mating) 500 cycles (For Beryllium Copper Contact).

·        Antenna GSM -2DBI Rubber Duck R/A SMA

·        4g Antenna GSM 6DBI Springy Magnetic Stand Base Antenna With 3m Cable With SMA Male Connector

·        2.4GHz 6DBI Antenna

·        White Color 5DBI 4G LTE Antenna With SMA Connector

·        Antenna GSM-2DBI Magnetic Antenna

·        GSM-3DBI Magnetic Spring Antenna

·        2.4GHz 2DBI Antenna

·        Female Right Angle SMA Connector

·        GSM-6DBI Magnetic Spring Antenna

·        PCB Edge Mountable Female SMA Connector

·        GSM- 2DBI Sticker Antenna

·        Antenna GPS 3V Magnetic Mount SMA

·        Female Straight SMA Connector

·        Interface Cable RP-SMA to U.FL

·        U.FL SMD Connector

·        GSM PCB ANTENNA

·        STICKER ANTENNA .

This is Rubber Duck Antenna With SMA-Male Right Angle Foldable Connector with Frequency of 824 960 MHz & 1710 1980 MHz and 2 dBi Gain. The High-Gain Directional Indoor Antenna is used to extend the range of wireless network coverage in a single direction. It can be attached to an access point, wireless router, or wireless network adapter. Ideal when access points and routers need to be placed in wiring closets or inside ceilings, since you can locate this antenna at the top of a cubicle, on a ceiling, on a desktop or on the wall, optimizing your wireless coverage.

Application: GSM

1. Compact Size
2. Low Cost
3. Straight version available
4. SMA-Male Plug connectors available.

This is a GSM Antenna having a frequency of 824 – 960 MHz & 1710 – 1980 MHz with 28dBi gain. The antenna is a wireless device to receive and transmit signals, it has been widely used in telecommunication to communicate. One of the main reasons to use a sticker antenna is the reduced overall cost of the radio module.

Application: GSM

1. Compact Size
2. Low Cost
3. The connector of your choice
4. Any cable length (suggested <5m)
5. Frequency (MHz) : 824 – 960 MHz & 1710 – 1980 MHz
6. Gain:2 / 3 dBi
7. Impedance (Ω): 50
8. Connector Type: SMA Plug
9. VSWR :< 2.5
10. Cable Length: 3 Meter

This is an interface cable that connects an SMA Female Connector to a UFl connector. Use this cable to connect the tiny UFl connector on a PCB to an antenna with an SMA connector. The SMA Female connector in this cable can be mounted onto a panel.

SMA Female part is highly suitable for prototyping with the cellular devices and GPS that needs an antenna connection. The female signal pin present in this connector correctly mate with the original SMA type antenna and ensures reliable functioning. The other end of the cable fits with the U.FL connector. Use it to attach any standard RP-SMA 2.4GHz antenna to the DPAC 802.11 modules.

Features:

• RF Coaxial Cable, RP SMA Straight Female, 
• Used for Wireless communication and Wireless LAN;
• Pre-assembled with different RF connectors for choice. 

Appliance: 

• Mobile Phone
• PC
• GPS
• Network Storage Equipment
• Medical, Lighting
• Remote Control

• RF Cable
• IPX to SMA Female Cable
• 1.13 mm Cable
• 10 cm Length

• Antenna GSM -2DBI Rubber Duck R/A SMA

  4g Antenna GSM 6DBI Springy Magnetic Stand Base Antenna With 3m Cable With SMA Male Connector

  2.4GHz 6DBI Antenna

  White Color 5DBI 4G LTE Antenna With SMA Connector

  Antenna GSM-2DBI Magnetic Antenna

  GSM-3DBI Magnetic Spring Antenna

  2.4GHz 2DBI Antenna

  Female Right Angle SMA Connector

  GSM-6DBI Magnetic Spring Antenna

  PCB Edge Mountable Female SMA Connector

  GSM- 2DBI Sticker Antenna

  Antenna GPS 3V Magnetic Mount SMA

  Female Straight SMA Connector

  Interface Cable RP-SMA to U.FL

  U.FL SMD Connector

  GSM PCB ANTENNA

  STICKER ANTENNA

  .

This is a PCB Patch Antenna having a frequency of 1575 +/- 20MHz with > 2.5dBi dBi gain. PCB Antenna is a wireless device to receive and transmit signals, it has been widely used in GPS applications. One of the main reasons to use a PCB (printed circuit board) antenna is the reduced overall cost of the radio module.

This antenna comes with an IPEX MHF1 Female connector to connect with the application. (We can also arrange your Required connector if you need the antenna in bulk quantity)

Application: GPS

1.  Internal PCB Antenna for GPS Applications
2. Compact Size
3. High quality
4. Low cost
5. 3M high-quality adhesive
6. Masking for corrosion-free

This is Magnetic Mount Antenna having a frequency of 2400 2483 MHz and gain of 3 dBi. This is very helpful for signal boosting. Magnetic mount antennas are commonly used for car and truck applications. The antennas magnetic base sticks securely to the metal of the vehicle. The metal surface of the car acts as a ground plane to bounce the signal. Since magnetic mount antennas require a ground plane, they should be mounted on metal.

Application: 2.4 GHz Applications, Smart Meters

1. Compact Size
2. Low Cost
3. Anodized Aluminium

LAMBDOID hardware technology company specializing in RF & Solar products. Our prime focus is the design and manufacture of standard and customized RF solutions for the Telecommunication industry which includes RF Antennas, RF Devices, RF Shields, RF Cables and Assemblies, RF Connectors, etc.

An antenna is a device to transmit and receive electromagnetic waves. Electromagnetic waves are often referred to as radio waves. Most antennas are resonant devices, which operate efficiently over a relatively narrow frequency band. Antennas can be designed to transmit and receive radio waves in all horizontal directions equally (omnidirectional antennas), or preferentially in a particular direction. Here you can get an antenna for UBlox NEO GPS model, Antenna Base Set and many more GPS modules.

The rubber ducky antenna is an electrically short monopole antenna that functions somewhat like a base-loaded whip antenna. It consists of a springy wire in the shape of a narrow helix, sealed in a rubber or plastic jacket to protect the antenna. Rubber ducky antenna is a form of normal-mode helical antenna.

We have added full range of Lambdoid antenna explore more .

Application: GSM/ 2G, 3G, RFID

1. Compact Size
2. Low Cost
3. Easy to use
4. Plug and play deceive
5. Durable & hard body .

This is Magnetic Dual-Band Mount Antenna having a frequency of 824 – 960 MHz & 1710 – 2170 MHz and gain of 4/6 dBi. This antenna is supported to GSM FCT and other GSM Module/Modems. The biggest advantage to dual-band antennas is their ability to provide a strong, stable wireless connection is often difficult to reach locations. For this reason, they are often used in devices such as cellular or dual-band wireless access points. 

Application: GSM, 3G

1. Compact Size
2. Low Cost
3. SMA Male
4. Any cable length (suggested <5m)

This is a 15cm 3DBI GSM/GPRS/3G PCB Antenna with IPEX13 Connector. This PCB/Sticker Antenna is a wireless device to receive and transmit signals, it has been widely used in telecommunication to communicate. One of the main reasons to use a PCB (printed circuit board) antenna is the reduced overall cost of the radio module.

Application: 2G, 3G, 15dBi Applications 

1. Name: 2G 3G IPEX antenna
2. Connector type: ipx13
3. Gain definition: 3dBi (Typical)
4. Frequency band definition: 17102170MHz 800960
5. Impedance definition: 50 ohm
6. Total length: as shown in Figure
7. Impedance 50 Ohm
8. Material: PCB
9. Operating Temperature: 30 to ~ + 85°C

This is an Omni-directional antenna with an IPEX connector. Its working frequency is 2.4GHz which meets most requirements of Wi-Fi devices. With 6dBi high gain, it offers robust signal reception and transmission.

1. Frequency: 2.4 GHz
2. Gain: 6dBi
3. Cable Length: 15cm
4. Interface: IPEX MHF1
5. Supports LattePanda V1
6. Height: 170 mm/ 6.7 inches
7. Weight: 18g .

1. Radomematerial: polyurethane
2. Flexible cable
3. Stable signal
4. Best for indoor applications
5. Radome material: polyurethane
6. Flexible cable
7. Stable signal
8. Best for indoor applications.
9. Connector: IPX female to SMA-KY
10. Frequency(Hz): 900/1800
11. Gain: <3 dB
12. VSWR: <1.5  .

This is GSM 4G/3G/2G LTE Flexible Magnetic Mount Antenna having Frequency of 698 960 MHz & 1710 2690 MHz and 6/ 7 dBi Gain. This antenna is supported to GSM FCT of Micromax, and other GSM Module/Modems. Magnetic mount antennas are commonly used for car and truck applications. The antennas magnetic base sticks securely to the metal of the vehicle. The metal surface of the car acts as a ground plane to bounce the signal. Since magnetic mount antennas require a ground plane, they should be mounted on metal.

Application: GPRS, GSM, 3G,4G, ISM

1. Magnetic base indoor antenna.
2. High quality
3. low cost.
4. 20 x 2 mm Neodymium powerful magnets.
5. Chrome-plated available for 1K+ order quantity.

·        Antenna GSM -2DBI Rubber Duck R/A SMA

·        4g Antenna GSM 6DBI Springy Magnetic Stand Base Antenna With 3m Cable With SMA Male Connector

·        2.4GHz 6DBI Antenna

·        White Color 5DBI 4G LTE Antenna With SMA Connector

·        Antenna GSM-2DBI Magnetic Antenna

·        GSM-3DBI Magnetic Spring Antenna

·        2.4GHz 2DBI Antenna

·        Female Right Angle SMA Connector

·        GSM-6DBI Magnetic Spring Antenna

·        PCB Edge Mountable Female SMA Connector

·        GSM- 2DBI Sticker Antenna

·        Antenna GPS 3V Magnetic Mount SMA

·        Female Straight SMA Connector

·        Interface Cable RP-SMA to U.FL

·        U.FL SMD Connector

·        GSM PCB ANTENNA

·        STICKER ANTENNA .

ESP 8266 ESP8266 serial WIFI wireless transmitter module gain antenna MT76813DBI Module.

The subject of the auction is a set of elements needed to perform the modification of the Raspberry Pi Zero W tile so that it is possible to connect an external WiFi antenna. With this modification, you will increase the WiFi range in your Raspberry Pi Zero W. Factory-new components, 100% functional.

1. Radome material: polyurethane
2. Flexible cable
3. Stable signal
4. Best for indoor applications.

This GPS/GLONASS GNSS Antenna is designed for applications that require high positioning accuracy by combining signals from GPS, GLONASS, systems. The tiny size of this antenna allows it to be used in very space-restricted environments. With 3-meter long cable, one can use this antenna to enhance the GPS Signals in an indoor project with GPS and GSM modules as well as Raspberry Pi HAT or Arduino Shield.The Antenna has a flat magnetic surface to keep it steady at one place temporarily, or it can permanently stick to any surface with helpof Double Sided Tape

A high gain wide-band patch antenna on an integral ground delivers reliable performance. A fully IP67 waterproof rated and UV resistant enclosure allows use in outdoor environments. Mid SAW filter configuration eliminates potential. LNA burn-out from nearby out of band radiated power bursts from other antennas that may be co-located nearby.

1. The antenna assembly consists of a patch antenna for receiving GNSS signals and a preamplifier for signal amplification.
2. Power supply to the antenna pre-amplifier must be provided by the application on the same RF signal trace as the GNSS RF signal is carried to the application.
3. The antenna has an internal magnet so that it can be fixed on a metallic surface.
4. Easy to use an antenna. Does not require RF or antenna knowledge.

VHM-314 V3.0 Bluetooth Audio Receiver Board can be used in DIY kit. Using Bluetooth technology, the data can be transmitted to mobile phone and other devices, and the audio source is stable. The receiver is a Bluetooth module that connects to your radio and wired headset or speaker. RoboticsBD

The board is designed to be used for various electronic devices like mobile phones and tablets. The main board has lossless sound quality, no noise, no radiation, and no delay. Support the wireless audio function of the mobile phone, you can also use it as a single button control. Meanwhile, the main board is made of abs material, which can provide stable performance. The wireless receiving module is suitable for various kinds of Bluetooth devices such as smart phones and tablets. RoboticsBD

The Bluetooth receiver is a wireless communication device that connects to the computer with the help of simple button operation and can provide you with the latest wireless experience. As a wireless communication tool, it is suitable for the use of various electronic parts that are used in the fields. Support Bluetooth audio interface, can be used to connect mobile phones, computers and other devices with wireless receiving and transmitting function of music.

Additional Information:

• Delivery Time: standard