GU Impex

Nextion NX4832f035 is a 3.5 Discovery series SMART HMI Touch display having a resistive touch screen. The discovery series of Nextion displays are cost-effective HMI solutions based on STM32GO ARM Cortex-M0+ 64MHz Onboard MCU Processor. In the discovery series when the Deep Sleep Mode is activated, the devices working current is down to 0.25 mA. Your Battery Powered HMI device will last a longer working time with such a low power consumption. Compared to the Nextion basic series the discovery series reaches up to 30% more performance improvement.

Next Discovery NX4832f035 3.5 Resistive Touchscreen Display is so simple to the interface that it can easily work with Arduino, Raspberry Pi, ESP8266, ESP32, PIC Microcontroller, AVR controller, ARM Microcontroller and you wont believe it will work even with basic 8051 microcontrollers basically it will work with any board or Microcontroller that has UART port.

Nextion includes a hardware part (a series of TFT boards) and a software part (theNextion editor). The Nextion TFT board uses only one serial port to communicate. Nextion editor has mass components such as button, text, progress bar, slider, instrument panel etc. to enrich the interface design. And the drag-and-drop function ensures that users spend less time in programming. With the help of this WYSIWYG editor, designing a GUI is a piece of cake.

1. 3.5 LCD-TFT Resistive HMI touch display module
2. 480 x 320 screen resolution
3. RGB 65K true-to-life colours
4. Onboard ARM Cortex-M0+ 64MHz MCU
5. 3584 Byte SRAM
6. 16 MB Flash memory
7. XH2.54 4 Pins (+5V, TX, RX, GND) TTL serial interface .

This 2.4-inch SPI Interface 240×320 TFT Display Module has always been one of the hot products in DIY industry and LCD is basically the necessary products during all projects, at the same time, serial port modules are also the popular ones because it takes few IO and the usage is simple. This section of the 2.4S-inch TFT LCD serial SPI integrated features of compact,

Pin Description:

1. SDO: Serial clock output
2. LED: 3.3V IO and Power Supply pin
3. SCL: Serial clock input
4. SDA / SDI: Serial data input
5. DC: Data / Command selection
6. RST: Reset, Low level active
7. CS: Chip Selection, Low level active
8. GND: Ground
9. VDD33: 3.3V Power Supply pin
10. UTFT Support

1. It is a 2.4″ SPI TFT LCD  Module
2. 10pins interface.
3. Not just an LCD break but include SD card (2GB),
4. The LCD drive ic is ILI9341.
5. It’s a 240 * 320 (resolution),
6. Touch: No
7. 2.4 inch TFT LCD screen.
8. The LCD has a wide viewing angle, the contrast is also very suitable.
9. The display interface is serial, it just needs 5 wires (CS, RS, SCL, SDA, RST) for controlling.
10. SDcard use hardware SPI interface (CS / MOSI / MISO / SCK), Not solder pins.

1 x 2.4-inch SPI Interface 240×320 TFT Display Module

This 2.4 inch SPI Interface 240×320 Touch Screen TFT Colour Display Module has always been one of the hot products in DIY industry and LCD is basically the necessary products during all projects, at the same time, serial port modules are also the popular ones because it takes few IO and the usage is simple. This section of the 2.4S-inch TFT LCD serial SPI integrated features of compact, SPI interface.

Pin Description:

1. SDO: Serial clock output
2. LED: 3.3V IO and Power Supply pin
3. SCL: Serial clock input
4. SDA / SDI: Serial data input
5. DC: Data / Command selection
6. RST: Reset, Low level active
7. CS: Chip Selection, Low level active
8. GND: Ground
9. VDD33: 3.3V Power Supply pin
10. UTFT Support

1. It is a 2.4inch SPI TFT LCD Screen Module
2. 10pins interface.
3. Not just an LCD break but include SD card (2GB),
4. The LCD drive ic is ILI9341.
5. It’s a 240 * 320 (resolution),
6. 2.4 inch TFT LCD screen.
7. The LCD has a wide viewing angle, the contrast is also very suitable.
8. The display interface is serial, it just needs 5 wires (CS, RS, SCL, SDA, RST) for controlling.
9. SDcard use hardware SPI interface (CS / MOSI / MISO / SCK), Not solder pins.

1 x 2.4-inch SPI Interface 240×320 Touch Screen TFT Display Module

1 x Stylus Pen

Nextion NX3224F024 is a 2.4″ Discovery series SMART HMI Touch display having a resistive touch screen. The discovery series of Nextion displays are cost-effective HMI solutions based on STM32GO ARM Cortex-M0+ 64MHz Onboard MCU Processor. In the discovery series when the Deep Sleep Mode is activated, the device’s working current is down to 0.25 mA. Your Battery Powered HMI device will last a longer working time with such a low power consumption. Compared to the Nextion basic series the discovery series reaches up to 30% more performance improvement.

Nextion Discovery NX3224F024 2.4inch Resistive Touch Display is so simple to the interface that it can easily work with Arduino, Raspberry Pi, ESP8266, ESP32, PIC Microcontroller, AVR controller, ARM Microcontroller and you won’t believe it will work even with basic 8051 microcontrollers basically it will work with any board or Microcontroller that has UART port.

Nextion includes a hardware part (a series of TFT boards) and a software part (the Nextion editor). The Nextion TFT board uses only one serial port to communicate. Nextion editor has mass components such as button, text, progress bar, slider, instrument panel etc. to enrich the interface design. And the drag-and-drop function ensures that users spend less time in programming. With the help of this WYSIWYG editor, designing a GUI is a piece of cake.

1. 2.4” LCD-TFT Resistive HMI touch display module
2. RGB 65K true-to-life colours
3. Onboard ARM® Cortex®-M0+ 64MHz MCU
4. 3584 Byte SRAM
5. 4 MB Flash memory
6. XH2.54 4 Pins (+5V, TX, RX, GND) TTL serial interface

1. 1 × 2.4inch Nextion HMI Display
2. 1 × power supply test board
3. 1 x 4-pin grove cable

The 3.5 inch TFT LCD Touch Display Shield for Arduino Uno is fully assembled, tested and ready to go. Add the touch display without wiring, no soldering! Simply plug it in and load up a library – you’ll have it running in under 10 minutes! Works best with any classic Arduino ATMEGA328 Board

So spice up your Arduino UNO project with a beautiful large touchscreen display shield with a built-in microSD card connection. This TFT display is big (3.5″ diagonal) bright (4 white-LED backlights) and colorful (18-bit 262,000 different shades)!

The Display comes with 480×320 pixels with individual pixel control. It has way more resolution than a black and white 128×64 display.  As a bonus, this display has a resistive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

1. 3.5″ diagonal LCD TFT display, with bright 4 white-LED backlights, default state: on
2. It can control the backlight to connect the transistor to a digital pin
3. 480×320 Pixels, with colorful and 18-bit, 262,000 different kinds of shade
4. 4-wire resistive touchscreen
5. 8-bit digital interface, plus 4 control lines

1 x 3.5″ inch ILI9486 TFT Touch Shield LCD Module 480×320 for Arduino Uno

1 x Stylus

3.5″ inch ILI9486 TFT  LCD Module 480×320 for Arduino Uno without Stylus is a compact yet powerful display solution designed specifically for Arduino Uno boards. With a high-resolution 480×320 screen, it offers crisp and clear visuals for your projects. This module boasts compatibility with Arduino Uno, making it easy to integrate into your existing projects. Whether you’re building a smart home dashboard, a portable gaming device, or an interactive art installation, this LCD Module provides a vibrant canvas for your creativity.

1. 3.5″ diagonal LCD TFT display, with bright 4 white-LED backlights, default state: on
2. It can control the backlight to connect the transistor to a digital pin
3. 480×320 Pixels, with colorful and 18-bit, 262,000 different kinds of shade
4. 8-bit digital interface, plus 4 control lines

1 x 3.5″ inch ILI9486 TFT  LCD Module 480×320 for Arduino Uno without Stylus

This TFT display is big bright and colorful! 480×320 pixels with individual RGB pixel control, this has way more resolution than a black and white 128×64 display.

As a bonus, this display has a resistive touch screen attached to it already, so you can detect finger presses anywhere on the screen. This display has a controller built into it with RAM buffering so that almost no work is done by the microcontroller.

This 3.5-inch SPI Touch Screen Module is wrapped up into an easy-to-use breakout board, with SPI connections on one end. If you’re going with SPI mode, you can also take advantage of the onboard MicroSD card socket to display images.

The 3.5-inch display doesn't have a built-in level shifter, so it's advised to use only 3.3v. Using a node MCU would be more suitable cause it provides only 3.3v. if you are using a 5v microcontroller like the Arduino UNO, MEGA, Using a level shifter would give you the appropriate voltage needed to operate the LCD without damaging it.

HMI Displays are becoming increasingly popular as a result of their intelligence, and NEXTION is one of the major players in HMI Display Production, which has introduced a range of different kinds of Displays at a very affordable cost.

NEXTION offers an advanced level of displays at an affordable cost than any other competitor brand in the market, making them ideal for the one who wants to start some Projects through touch displays. This type of Display has inbuilt audio, video, and animation play functions which makes it smart.

Nextion Enhanced NX8048K050 5.0” HMI Touch Display is a seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application, or appliance. The operating Voltage of the Display is lies between 4.75 to 7 V also with 32MB Flash data storage space, 1024 byte EEPROM, 8192 byte RAM. With GPIO supported, now customers can use Nextion to control external devices. Using the NEXTION Editor software, you can quickly develop the HMI GUI by drag-and-drop components (graphics, text, button, slider, etc.) and ASCII text-based instructions for coding how components interact at the display side. Nextion HMI display connects to peripheral MCU via TTL Serial (5V, TX, RX, GND) to provide event notifications that peripheral MCU can act on, the peripheral MCU can easily update progress, and status back to Nextion display utilizing simple ASCII text-based instructions.

1. Supports built-in RTC
2. Supports GPIO
3. SD Card interface: support max 32G Micro TF/SD card (FAT32 file format)
4. Flash data storage space: 32MB
5. EEPROM: 1024 bytes
6. RAM: 8192 bytes
7. Instruction buffer: 1024 bytes
8. Color: 65K (65536) colors
9. Resolution: 800×480 pixel
10. Adjustable Brightness:0~230 nit- the interval of adjustment is 1%
11. Certificates: CE/EMC, RoHS (certificates).

2.9-inch e-Ink Paper Display Module with SPI Interface is an E-Ink display module, 2.9inch, 296128 resolution, with an embedded controller, communicating via SPI interface, supports partial refresh. Due to the advantages like ultra-low power consumption, wide viewing angle, great effect under sunlight, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.

There is no backlight so it can keep displaying last content for a long time even when the power is down. As these displays have no backlight panels and it doesn't need a continuous power supply to display the (static data with periodic intervals) data on the screen, it has a great advantage of ultra-low power consumption. Also, it has a wide viewing angle, great viewing effect under sunlight, Basically power to the display is only required for refreshing. For connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.. SPI interface can be used.

1. No backlight keeps displaying last content for a long time even when a power down
2. Ultra low power consumption, basically power is only required for refreshing
3. SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.
4. Onboard voltage translator, compatible with 3.3V/5V MCUs
5. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)

Waveshare 1.54 inch e-Ink Paper Display Module with SPI Interface comes with 200×200 resolution and embedded controller module. It is communicating via SPI interface and it supports partial refresh. As these displays have no backlight panels and it doesn’t need a continuous power supply to display the (static data with periodic intervals) data on the screen, it has a great advantage of ultra-low power consumption. Also, it has a wide viewing angle, great viewing effect under sunlight, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.

1. No backlight so keeps displaying last content for a long time even when the power is down
2. Ultra low power consumption, basically power is only required for refreshing
3. SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.
4. Comes with development resources and manual (examples for Raspberry Pi/Arduino/STM32)
5. Wide viewing angle, great viewing effect under sunlight.
6. Display Resolution: 200 x 200
7. Display Screen Color: Black and White

The Nextion Enhanced NX4827K043 Generic 4.3 HMI Touch Display is more powerful than the standard ones. Compare to the basic Nextion displays, the enhanced ones have added some new functions, such as: supporting built-in RTC, supporting save data to Flash, supporting GPIO, larger flash capacity, and larger CPU clock. The enhanced Nextion series has 7 size covers from generic 2.4 to 7.0.

Nextion is a Seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly applied to the Internet of Things (IoT) or the consumer electronics field. It is the best solution to replace the traditional LCD and LED Nixie tubes.

1. Supports built-in RTC
2. Supports GPIO
3. SD Card interface: support max 32G Micro TF/SD card (FAT32 file format)
4. Flash data storage space: 32MB
5. EEPROM: 1024 bytes
6. RAM: 8192 bytes
7. Instruction buffer: 1024 bytes.

Nextion Enhanced NX3224K028 is a powerful 2.8” HMI TFT display, with 16MB Flash data storage space, 1024 bytes EEPROM,  3584 bytes RAM. With GPIO supported, now customers can use Nextion to control external devices.

Nextion is a seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly applied to the Internet of thing (IoT) or the consumer electronics field. It is the best solution to replace the traditional LCD and LED Nixie tube.

Nextion includes a hardware part (a series of TFT boards) and a software part (the Nextion editor). The Nextion TFT board uses only one serial port to communicate. It lets users avoid the hassle of wiring. We noticed that most engineers spend much time in application development but get unsatisfactory results. As a solution to this situation, Nextion editor has mass components such as button, text, progress bar, slider, instrument panel etc. to enrich the interface design.

Furthermore, the drag-and-drop function ensures that users spend less time in programming, which will reduce 99% of their development workloads. With the help of this WYSIWYG editor, designing a GUI is a piece of cake. It’s easy to adapt Nextion family HMI to existing projects- users just need to provide it a UART.

1. Supports built-in RTC
2. Supports GPIO
3. SD Card interface: support max 32G Micro TF/SD card (FAT32 file format)
4. Instruction buffer: 1024 bytes
5. Color: 65K (65536) colors
6. Resolution: 320×240 pixel
7. Adjustable Brightness:0~180 nit- the interval of adjustment is 1%
8. Certificates: CE/EMC, RoHS (certificates)

The Nextion Enhanced NX3224K024 display is powerful than the standard ones. Compare to the basic Nextion displays, the enhanced ones have added some new functions, such as: supporting built-in RTC, supporting save data to Flash, supporting GPIO, larger flash capacity, and larger CPU clock. The enhanced Nextion series has 7 size covers from generic 2.4” to 7.0”.

Nextion Enhanced NX3224K024 is a powerful 2.4” HMI TFT display, with 16MB Flash data storage space, 1024 bytes EEPROM and larger RAM of 3584 bytes. With GPIO supported, now customers can use Nextion to control external devices.

Nextion Enhanced NX3224K024 – Generic 2.4” HMI Touch Display is a Seamless Human Machine Interface (HMI) solution that provides a control and visualization interface between a human and a process, machine, application or appliance. Nextion is mainly applied to the Internet of Things (IoT) or the consumer electronics field. It is the best solution to replace the traditional LCD and LED Nixie tubes.

Nextion includes a hardware part (a series of TFT boards) and a software part (the Nextion editor). The Nextion TFT board uses only one serial port to communicate. It lets users avoid the hassle of wiring. We noticed that most engineers spend much time on application development but get unsatisfactory results. As a solution to this situation, Nextion editor has mass components such as button, text, progress bar, slider, instrument panel etc. to enrich the interface design. And the drag-and-drop function ensures that users spend less time in programming, which will reduce 99% of your development workloads. With the help of this WYSIWYG editor, designing a GUI is a piece of cake. It’s easy to adapt Nextion family HMI to existing projects- users just need to provide it a UART.

1. Supports built-in RTC
2. Supports GPIO
3. SD Card interface: support max 32G Micro TF/SD card (FAT32 file format)
4. Flash data storage space: 16MB
5. EEPROM: 1024 bytes
6. RAM: 3584 bytes
7. Instruction buffer: 1024 bytes
8. Color: 65K (65536) colors
9. Resolution: 320×240 pixel
10. Adjustable Brightness: 0~180 nit – the interval of adjustment is 1%

Waveshare 4.3 Inch Capacitive Touch Display has an IPS display panel and a screen resolution of 800×480. This display has a capacitive touch-type screen and toughened glass touch panel that supports Raspberry Pi. Also, it has a DSI port for displaying, MIPI DSI Interface, and touch control.

Working With Raspberry Pi 4

Supports Pi 4B/3B+/3A+/3B/2B/B+/A+, CM3/3+*

1. 4.3 inch IPS screen. 800×480 hardware resolution.
2. Capacitive touch panel, support 5-point touch.
3. Supports Pi 4B/3B+/3A+/3B/2B/B+/A+.
4. Another adapter board is required for CM3/3+.
5. DSI interface, refresh rate up to 60Hz.
6. Supports Raspbian/Ubuntu/Kali and WIN 10 IoT, driver-free.

Nextion is a Human Machine Interface HMI solution combining an onboard processor and memory touch display with Nextion Editor software for HMI GUI project development. Using the NEXION Editor software, you can quickly develop the HMI GUI by drag-and-drop components (graphics, text, button, slider, etc.) and ASCII text-based instructions for coding how components interact on the display side. Nextion HMI display connects to peripheral MCU via TTL Serial (5V, TX, RX, GND) to provide event notifications that peripheral MCU can act on, the peripheral MCU can easily update progress and status back to Nextion display utilizing simple ASCII text-based instructions.

The Intelligent Series products have more powerful hardware in terms of MCU, Flash storage, and SRAM compared with Basic Series and Enhanced Series. Whats more and new? The audio, video, and animation play functions enrich the users project HMI interaction. The Intelligent Series supports advanced software features and functions such as transparent component, page loading effect, component Move, and Drag .etc.

1. Nexiton Display Type: Intelligent Series
2. Nexiton Model: NX8048P070-011R-Y(18.1 cm resistive touchscreen with enclosure)
3. Built-in RTC support (Battery type: CR1220)
4. Operating Voltage:5V-6.5V
5. Operating Current: 530mA(VCC=+5V, Brightness is 100%).